ASM Haltech standalone ECU

1,999.99 €
Hors taxe: 420.00 €
État de stock: please contact us.

pcs

We've developed a plug and play solution for integrating the Haltech Elite series of stand alone ECU's into a NSX.

This in our opinion is the best value and easiest to use with the most advanced features available for a stand-alone ECU.

Only surpassed by considerably more expensive Motec ECU kits.

Our kits offer a complete replacement for engine control and traction control in one fully programmable system plug and play for NSX.

Kits come with a 3D printed wiring loom that features OEM connectors and shielded extensions.

Further more it also offers limp and contingency modes, data logging, streaming, and compatible with GaugeART for dual din screens. 

It also works with the OEM Honda dashboard

We use the Haltech system on all our in-house Turbo and NA builds, it provides a OEM running engine with all the stock features.

Yet fully programmable and the ability to adapt to conditions far better than any OEM ECU allowing ITB's to run smoothly, high boost cars to idle and start as stock.

For NSX applications we offer ether 2000 series or 2500 series.

2000 are great for single turbo and 90-94 NSX, 2500 adds better dual wideband and DBW plus a additional layer of contingencies.


Pricing 

Elite 2000 = €1999,95 

Elite 2500 =  €2500




features for the 2000

FEATURES

• 8 x Fuel Injection Outputs

• 8 x Ignition Outputs

• 12 x Digital Outputs

• 10 x Analogue Voltage Inputs

• 4 x Synchronised Pulsed Inputs

• 4 x Dedicated Inputs (Dual Knock, ignition Switch & Internal MAP Sensor)

• 2 x Dedicated Engine Position Inputs with extensive trigger type support

• USB Laptop Communications

• Programmable Injector Peak and Hold Currents

• ESP Calibration Software – Intuitive and easy to use

• Dual CAN Bus communication for OBDII and Haltech CAN Expansion

• OBDII Compatible – Set and clear diagnostic trouble codes, view live engine data

• Variable cam control – Independently control up to 2 Intake camshafts

• Short and Long term fuel, cam, boost and idle control learning

• Dual Channel Knock Control – with high speed digital filtering for accurate detection

• Multi-fuel Support – Support for Petrol (Gasoline),LPG, Methanol and Ethanol

• E85 Flex Fuel Ready – Direct connection to sensor

• Closed Loop 3D Boost Control – Multiple Modes – Tune by gear, wheel speed or time

• Nitrous Control – Wet, Dry or progressive with 3D Fuel and ignition corrections & On/off delays

• Closed Loop Idle Control – With learning for consistent idle stability

• Closed Loop 02 Control – Dual bank control

(with optional external CAN O2 Wideband Controller Kit)

• Anti-Lag/rotational idle and Launch Control – Drag and Rally modes

• Rolling Anti-Lag – Fixed or current, RPM or road speed

• Flat Shift function

• Data logging 1 MB internal memory – Up to 20 channels of logging.

Sampling rates up to 50ms (20Hz) & external laptop logging using available hard drive memory

• Engine Protection – Set limits for sensors and protect your engine

• Internal 3 Bar MAP Sensor (29 psi max boost)

SPECIFICATIONS

Fuel Injector Outputs:

• 8 x Current controlled injector drivers

• High or Low impedance injector compatible

• Programmable Peak Current – 0A – 8A

• Programmable Hold Current – 0A – 2A

• All spare injector outputs can be used as generic DPOs with 1A Max output.

Ignition Outputs:

• 8 x Over current protected ignition drivers

• Max current 1A per driver

• All spare ignition outputs can be used as generic DPOs with 1A Max output

Digital Pulsed outputs:

• 5 x Over current protected low side pulsed outputs

• 1 x Dedicated engine control relay output which can control up to 6 relays simultaneously

Stepper Motor Control:

• 1 x 4 wire stepper motor control

• Can be configured as 4 x hi / low side outputs

• Max drive current 1A per output

• Max sink current 1A per output

• Over current protected

Knock Inputs:

• 2 x Dedicated Knock Inputs

• Supports piezo knock sensors

• Synchronised to engine position

Analogue Voltage Inputs:

• 10 x Analogue Voltage Inputs

• 2 of which are compatible with narrowband O2 sensors

• Switchable 1K Ohm Pull-up resistor for sensors

• Can tolerate up to 20V Max input voltage

• Supports up to 1.5KHz input frequency

Engine Position Inputs:

• 2 x Engine Position Inputs with extensive trigger type support

• Supports variable reluctor and digital inputs

Synchronised Pulsed Inputs:

• 4 x Synchronised Pulsed Inputs

• Supports digital inputs ONLY

• Supports variable reluctor and digital sensors

• Measures duty cycle, frequency or state of a signal

• 50KHz Max frequency

• Can tolerate up to 25V Max input voltage

Internal Map Sensor:

• 3 Bar Internal MAP Sensor rated up to 200kPa of Boost (2bar/29psi)

Communication:

• 2 x CAN Bus communication for Haltech CAN Expansion and OBDII

• 1 x USB Connection for Programming

Data Logging:

• On-board Data Logging

• Data logging,Up to 20 channels of logging,

• Fastest Sample Rate 50ms

• 1MB Internal Storage

features for the 2500

Features:

• Waterproof Case (IP67) (With Pocket Cover Fitted)

• Drive by wire

• 8 x Fuel Injection Outputs

• 8 x Ignition Outputs

• 28 x Digital Outputs

• 10 x Analogue Voltage Inputs

• USB Laptop Communications up to 1 MB/s

• 6 x Engine Position Inputs with extensive trigger type support

• Programmable Injector Peak and Hold Currents

• OBDII Capable – Set and clear diagnostic trouble codes, view live engine data

• ESP Calibration Software – Intuitive and easy to use

• Dual CAN Bus communication for OEM and Haltech CAN Expansion

• User definable 5D Tuning – Tune by gear, Cam angle or any channel for ultimate flexibility

• Variable cam control – Independently control up to 4 camshafts Auto tune capabilities –

• Short and Long term fuel, ignition, boost and idle control learning

• Dual Channel Knock Control – with high speed digital filtering for accurate detection

• Multi-fuel Support – Support for Petrol (Gasoline),LPG, Methanol and Ethanol

• E85 Flex Fuel Ready – Direct connection to sensor.

• Closed Loop Boost Control – Multiple Modes – Tune by gear, wheel speed or time

• Closed Loop Idle Control – With learning for consistent idle stability

• Closed Loop 02 Control – Dual bank control for precise tuning

• Anti-Lag and Launch Control – Drag and Rally modes

• Data logging – Up to 40 channels of logging. Sampling rates up to 5ms

• Multi Level Engine Protection – Set limits for sensors and protect your engine

Outputs:

• 8 x Fuel Injector Outputs

– Current controlled injector drivers

– High or Low impedance injector compatible

– Programmable Peak Current – 0A – 8A

– Programmable Hold Current – 0A – 2A

– All spare injector outputs can be used as generic DPOs with 1A Max output.

• 8 x Ignition Outputs

– Over current protected ignition drivers

– Max current 1A per driver

– All spare ignition outputs can be used as generic DPO’s with 1A Max output.

• 6 x Digital Pulsed Outputs

– 5 x Over current protected low side pulsed outputs

– 1 x Dedicated engine control relay output which can control up to 6 relays simultaneously

• 2 x Drive By Wire Outputs

– Over current protected hi / low side motor outputs

– Suits most OEM throttle bodies and pedals

– Max Current 5A per driver

– 1A Average current

– 100KHz Max frequency

• 1 x 4 wire Stepper Motor Control

– Can be configured as 4 x hi / low side outputs

– Max drive current 1A per output

– Max sink current 1A per output

– Over current protected

Inputs:

• 10 x Analogue Voltage Inputs

– 2 are compatible with narrowband O2 sensors

– Switchable 1K Ohm Pull-up resistor for sensors

– Can tolerate up to 20V Max input voltage

– Supports up to 1.5KHz input frequency

• 2 x Engine Position Inputs

– Extensive trigger type support

• 4 x Synchronised Pulsed Inputs

– Supports variable reluctor and digital inputs

– 50KHz Max frequency

– Rated up to 20V Max input voltage

• 2 x Knock Inputs

– Supports piezo knock sensors

– Synchronised to engine position

Communications:

• 1 x CAN Bus communication for Haltech CAN expansion

• 1 x USB connection for programming

Data Logging

• On-board Data Logging, Up to 40 channels

• Fastest Sample Rate 5ms

• 1MB Internal Storage

Nous utilisons des cookies pour le fonctionnement de ce site. En l'utilisant , vous êtes d'accord sur leurs utilisations.